Glossary entry (derived from question below)
English term or phrase:
heel measurement for tool type ring
Polish translation:
pomiar średnicy zewnętrznej koła zębatego
Added to glossary by
Frank Szmulowicz, Ph. D.
May 15, 2020 13:46
3 yrs ago
7 viewers *
English term
Heel measurement for tool type ring
English to Polish
Tech/Engineering
Metrology
Heel measurement for tool type ring
Jest to jedna z czynności przeprowadzana przez mod ul oprogramowania pomiarowego (pomiar kół zębatych i łopatek).
O co chodzi w wyrażeniu "heel measurement"?
Z góry dziękuję za pomoc.
O co chodzi w wyrażeniu "heel measurement"?
Z góry dziękuję za pomoc.
Proposed translations
(Polish)
3 | pomiar średnicy zewnętrznej koła zębatego | Frank Szmulowicz, Ph. D. |
Change log
May 20, 2020 12:13: Frank Szmulowicz, Ph. D. Created KOG entry
Proposed translations
2 hrs
Selected
pomiar średnicy zewnętrznej koła zębatego
if this is a ring gear, then we have koło zębate koronowe.
cccccccc
The TOE of the gear is the portion of the tooth surface at the end
towards the center. The HEEL of the gear tooth is the portion of
the tooth surface at the outer-end. The TOP LAND of a gear tooth
is the surface of the top of the tooth. Every gear has a
characteristic pattern.
https://www.canadawideparts.com/downloads/dana_tooth_pattern...
ccc
https://www.cartechbooks.com/media/wysiwyg/43_4.jpg
cccccccccccccccccccccccccccccccccccccc
cccccccccccccccc
Gear Tooth Geometry
Before we go further, we need to discuss gear tooth geometry and nomenclature. The hypoid ring-gear tooth surface is broken into several different areas. The reason for this is to have a method to accurately describe where the bench contact pattern is located.
The heel is the outside diameter of the gear.
The toe is on the inside diameter.
https://www.cartechbooks.com/techtips/ring-and-pinion-gear-s...
ccccccccc
C – Heel. The outside-diameter-end of the gear tooth / Zewnętrzna średnica koła zębatego
https://zygadlo.pl/wp-content/uploads/2016/08/coast.png
https://zygadlo.pl/ustawienie-dyfra/
cccccccc
The TOE of the gear is the portion of the tooth surface at the end
towards the center. The HEEL of the gear tooth is the portion of
the tooth surface at the outer-end. The TOP LAND of a gear tooth
is the surface of the top of the tooth. Every gear has a
characteristic pattern.
https://www.canadawideparts.com/downloads/dana_tooth_pattern...
ccc
https://www.cartechbooks.com/media/wysiwyg/43_4.jpg
cccccccccccccccccccccccccccccccccccccc
cccccccccccccccc
Gear Tooth Geometry
Before we go further, we need to discuss gear tooth geometry and nomenclature. The hypoid ring-gear tooth surface is broken into several different areas. The reason for this is to have a method to accurately describe where the bench contact pattern is located.
The heel is the outside diameter of the gear.
The toe is on the inside diameter.
https://www.cartechbooks.com/techtips/ring-and-pinion-gear-s...
ccccccccc
C – Heel. The outside-diameter-end of the gear tooth / Zewnętrzna średnica koła zębatego
https://zygadlo.pl/wp-content/uploads/2016/08/coast.png
https://zygadlo.pl/ustawienie-dyfra/
4 KudoZ points awarded for this answer.
Discussion